greece good quality foamed form - in-place foam gasket technology

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • Gasketing (FIPFG)

    With the FIPFG (Formed-In-Place-Foam-Gasket) technology, we meet the high demands of our customers for sealing quality and contour-accurate tightness of the components. Our more than 1000 material formulations offer a wide range of properties. Adhesion, temperature stability, elasticity, mechanical load capacity and chemical resistance are the ...

    Get Price
  • Foam-In-Place Gasket Service

    Foam-In-Place Gasketing Service As a full-service custom molder, Falcon Plastics is one of few molders that offer customers formed in place foam gasket technology (FIPG and FIPFG). This is a foam-in-place technology that forms superior, cut resistant gaskets …

    Get Price
  • SONDERHOFF FERMAPOR K31

    SONDERHOFF FERMAPOR K31 is the two-component polyurethane system to produce soft elastic foam gaskets, which are foamed directly onto the part using FIPFG technology (Formed-In-Place-Foam-Gasket). They are directly foamed onto the part with the aid of mixing and dispensing systems and FIPFG sealing technology (Formed-In-Place Foam Gasket).

    Get Price
  • Foam-in-place

    The foam-in-place (FIP) process is a reaction of polyurethane chemicals that creates foam, which is used to fill voids in cut-and-sewn laminate parts as well as between two parts of a mold. Our Dureflex® and Platilon® thermoplastic polyurethane films can be used as a barrier to prevent reacting polyurethane foam from penetrating the laminate ...

    Get Price
  • sonderhoff.com

    SONDERHOFF has been a Henkel brand since January 1, 2020 and complements the Henkel product portfolio as a technology platform for customized automated sealing, bonding and potting solutions. We are your process expert for the Formed-In-Place-(Foam-Gasket) FIP(FG) technology.

    Get Price
  • Form-in-place and cure-in-place gaskets

    When an assembly process proves to be even a tad too costly—even a penny or less per cycle—a cheaper alternative must be found. This is why many manufacturers have replaced die-cut or molded solid gaskets with form-inplace (FIP) and cure-in-place (CIP) liquid gaskets. A liquid gasket is dispensed onto a substrate to provide 100 percent contact between mating plastic, metal or wood surfaces.

    Get Price
  • From thermoplastics to liquid silicone rubber (LSR ...

    Precise protection for electronic components – with formed-in-place foam gaskets. Thanks to the FIPFG process, gaskets can be foamed directly into the component irrespective of the tool used and by means of a CNC-controlled system. PUR seals never lose their shape and fit perfectly, even in complex geometries.

    Get Price
  • Foam In Place Packaging Systems

    The SmartSHOT handheld foam in place system is designed for small, medium and large protective packaging applications that require both packaging protection and packaging damage prevention. The SmartSHOT protects products with conventional or anti-static SmartFILM available in 36 and 48-inch centerfold and 48-inch flat film. A variety of SmartFOAM A/B chemical densities and SmartLUBE Foam in ...

    Get Price
  • Sonderhoff Gasketing Total Process Solution for Low ...

    The conventional manual process employed requires line operators to peel and stick foam gaskets into place on the enclosure system housing. The process is error-prone and time-consuming. Accelerated manufacturing volumes must be cost-neutral at best, preferably cost-down as the enclosure market is competitive.

    Get Price
  • Cold Recycling with Foamed Bitumen

    State-of-the-art technology is used to produce foamed bitumen from normal bitumen which has been heated to approximately 175°C. With the in-situ method, a precisely dosed quantity of binding agent is added to mineral aggregate inside the WIRTGEN 2200 CR or 3800 CR cold recycler or the soil stabilizers of the WR series, using microprocessor ...

    Get Price
  • Foam In Place Packaging Systems

    The SmartSHOT handheld foam in place system is designed for small, medium and large protective packaging applications that require both packaging protection and packaging damage prevention. The SmartSHOT protects products with conventional or anti-static SmartFILM available in 36 and 48-inch centerfold and 48-inch flat film. A variety of SmartFOAM A/B chemical densities and SmartLUBE Foam …

    Get Price
  • From thermoplastics to liquid silicone rubber (LSR ...

    Precise protection for electronic components – with formed-in-place foam gaskets. Thanks to the FIPFG process, gaskets can be foamed directly into the component irrespective of the tool used and by means of a CNC-controlled system. PUR seals never lose their shape and fit perfectly, even in complex geometries.

    Get Price
  • DOWSIL™ 3-8209 Silicone Foam

    as a dispensed ‘foamed-in-place’ gasket material for the automotive and industrial assembly and maintenance industry. When the A and B liquid components are thoroughly mixed in a 1:1 ratio by volume, the product will expand and cure to a foamed elastomer in approximately 10 minutes at room temperature. This foam has a fine cell structure and

    Get Price
  • DOWSIL™ 3-8235 Silicone Foam

    Description DOWSIL™ 3-8235 Silicone Foam is a low to medium hardness product, primarily developed as a dispensable foamed in place compression gasket material. When the part A and part B liquid components are thoroughly mixed in a 1:1 ratio by weight, the product will expand and cure to a foamed elastomer.

    Get Price
  • Silicone Sponge Sheet

    Discover the benefits of kSil® Silicone Sponge & Foam Sheeting. Silicone Engineering’s kSil® sponge and foam sheeting provides the best quality …

    Get Price
  • Global Polyolefin Foam Suppliers

    Gasket fabricators are benefiting from the same, advanced precision engineering foam technology and reliable service that have had significant impact on the automotive and flooring industry. Tape and composite manufacturers are also tapping Toray for its foam innovations.

    Get Price
  • Vinyl Nitrile Closed Cell Foam - The Rubber Company

    Product Description. Our vinyl nitrile closed cell foam is a high quality material that features exceptional impact …

    Get Price
  • Cold Recycling with Foamed Bitumen

    State-of-the-art technology is used to produce foamed bitumen from normal bitumen which has been heated to approximately 175°C. With the in-situ method, a precisely dosed quantity of binding agent is added to mineral aggregate inside the WIRTGEN 2200 CR or 3800 CR cold recycler or the soil stabilizers of the WR series, using microprocessor ...

    Get Price
  • Application of foam bitumen in cold recycling and hydrated ...

    4.2.1. Foam bitumen characteristics. A Wirtgen WLB10 laboratory scale foam making unit was used to manufacture foam bitumen laboratory samples (Wirtgen Cold Recycling Technology, 2012).Two main characteristics of the foam bitumen were determined (Expansion ratio: maximum volume of foam relative to the original volume and the half life time (i.e. the time taken in seconds for the foam to ...

    Get Price
  • INSULATION OF PIPING & EQUIPMENT (PROJECT STANDARDS AND ...

    - Polyurethane blocks, segments or foamed in place sections for piping and vessels greater than DN900. Polyurethane foam shall conform to ASTM C591, Type 11, with a flame spread rating not exceeding 25 in accordance with ASTM E84. Higher density and higher strength foam may be used as load bearing insulation if the properties are approved.

    Get Price
  • Gasketing (FIPFG)

    With the FIPFG (Formed-In-Place-Foam-Gasket) technology, we meet the high demands of our customers for sealing quality and contour-accurate tightness of the components. Our more than 1000 material formulations offer a wide range of properties. Adhesion, temperature stability, elasticity, mechanical load capacity and chemical resistance are the ...

    Get Price
  • Foam-In-Place Gasket Service

    Foam-In-Place Gasketing Service As a full-service custom molder, Falcon Plastics is one of few molders that offer customers formed in place foam gasket technology (FIPG and FIPFG). This is a foam-in-place technology that forms superior, cut resistant gaskets for electrical enclosures, industrial lighting, and other applications in grooved parts.

    Get Price
  • SONDERHOFF FERMAPOR K31

    SONDERHOFF FERMAPOR K31 is the two-component polyurethane system to produce soft elastic foam gaskets, which are foamed directly onto the part using FIPFG technology (Formed-In-Place-Foam-Gasket). They are directly foamed onto the part with the aid of mixing and dispensing systems and FIPFG sealing technology (Formed-In-Place Foam Gasket).

    Get Price
  • Foam-in-place

    The foam-in-place (FIP) process is a reaction of polyurethane chemicals that creates foam, which is used to fill voids in cut-and-sewn laminate parts as well as between two parts of a mold. Our Dureflex® and Platilon® thermoplastic polyurethane films can be used as a barrier to prevent reacting polyurethane foam from penetrating the laminate ...

    Get Price
  • sonderhoff.com

    SONDERHOFF has been a Henkel brand since January 1, 2020 and complements the Henkel product portfolio as a technology platform for customized automated sealing, bonding and potting solutions. We are your process expert for the Formed-In-Place-(Foam-Gasket) FIP(FG) technology.

    Get Price
  • Form-in-place and cure-in-place gaskets

    When an assembly process proves to be even a tad too costly—even a penny or less per cycle—a cheaper alternative must be found. This is why many manufacturers have replaced die-cut or molded solid gaskets with form-inplace (FIP) and cure-in-place (CIP) liquid gaskets. A liquid gasket is dispensed onto a substrate to provide 100 percent contact between mating plastic, metal or wood surfaces.

    Get Price
  • From thermoplastics to liquid silicone rubber (LSR ...

    Precise protection for electronic components – with formed-in-place foam gaskets. Thanks to the FIPFG process, gaskets can be foamed directly into the component irrespective of the tool used and by means of a CNC-controlled system. PUR seals never lose their shape and fit perfectly, even in complex geometries.

    Get Price
  • Foam In Place Packaging Systems

    The SmartSHOT handheld foam in place system is designed for small, medium and large protective packaging applications that require both packaging protection and packaging damage prevention. The SmartSHOT protects products with conventional or anti-static SmartFILM available in 36 and 48-inch centerfold and 48-inch flat film. A variety of SmartFOAM A/B chemical densities and SmartLUBE Foam in ...

    Get Price
  • Sonderhoff Gasketing Total Process Solution for Low ...

    The conventional manual process employed requires line operators to peel and stick foam gaskets into place on the enclosure system housing. The process is error-prone and time-consuming. Accelerated manufacturing volumes must be cost-neutral at best, preferably cost-down as the enclosure market is competitive.

    Get Price
  • Cold Recycling with Foamed Bitumen

    State-of-the-art technology is used to produce foamed bitumen from normal bitumen which has been heated to approximately 175°C. With the in-situ method, a precisely dosed quantity of binding agent is added to mineral aggregate inside the WIRTGEN 2200 CR or 3800 CR cold recycler or the soil stabilizers of the WR series, using microprocessor ...

    Get Price
  • EPDM Closed Cell Foam - Fostek

    More information about Fostek EPDM Closed Cell Foam Fostek’s continuous roll technology produces EPDM closed cell foam rolls that range in gauge from 3mm thick to 32+ mm thick. We believe we have capability up to 38+mm, Fostek’s closed cell technology …

    Get Price
  • Foam Materials - UFP Technologies

    Foam: Polyethylene, Polyurethane& Specialty Materials. As one of the largest foam fabricators in North America, UFP Technologies has access to materials from the top suppliers from across the globe. We act as an extension of your in-house research, engineering and manufacturing teams, collaborating with you to determine the best materials for ...

    Get Price
  • Foam Fabrication Techniques: The Best Definitive Guide ...

    Foam products can be found everywhere such as sofa, chair, tape, insert packaging, baby pay mat, furniture and mattress upholstery. Here we are going to introduce how foam fabricators utilize a wide range of amazing foam fabrication techniques to make all sorts of foam products. Foam …

    Get Price
  • Gasket Attachment Applications

    Performance Factors for Gasket Attachment. 3M tapes, adhesives, sealers and fasteners offer a range of options for gasket attachment applications, whether you need to permanently bond panels to rigid frames, maintain elasticity for dynamic loads or allow for expansion when temperatures change. Use this list as a relative comparison of product ...

    Get Price
  • GASKET HANDBOOK 1 Edition - Fluid Sealing

    of several divisions with a specific product technology focus. As part of their mission they ... and installation best practices; with a focus on gasket selection and gasket-to-flange system interaction. Gasket storage and handling also are addressed. This Handbook is arranged and detailed to serve as a useful tool for ... reputable gasket ...

    Get Price
  • Germany Manufacturer producer plastic foam materials ...

    Germany: Browse through 98 Manufacturer producer in the plastic foam materials industry on Europages, a worldwide B2B sourcing platform.

    Get Price
  • EPE Foam: Properties, Uses, and Methods of Recycling ...

    EPE foam is a very flexible material compared to other forms of foam. EPE thus gives most protection for oddly shaped objects. 2. Superior Shock Absorbency: The closed cell structure of EPE foam makes it able to withstand and absorb high amounts of shock or stress and provide good cushioning to the object it is covering. 3. Regains Form …

    Get Price
  • SAVINA Foam Weather Stripping Anti-Collision for Doors and ...

    HIGH QUALITY MATERIAL: Equably Foamed by EPDM and High quality mesh adhesive. The roll D type foam seal strip, bottom size approx: 3/8in x 1/4in (9 x 6mm); Suitable gap: 1/8in to 13/64in (3-5mm). Each roll can be divided into 4 seals total 52 feet

    Get Price
  • A literature review on cold recycling technology of ...

    1. Introduction. As we all know, the development of road industry have made many achievements, especially in the highway engineering. However, due to the low level of technical process, lack of good quality materials, the unreasonable pavement design method, and the bad construction quality control and so forth, the early built asphalt pavement was damaged seriously and different types of ...

    Get Price
  • A review on insulation materials for energy conservation ...

    Loose-fillers spray foam, batts, blankets and rigid board are the four basic types of insulation. There are many factors need to be considered when choosing the insulation, such as construction type, rehabilitation plan and the code requirements .Several authors , , , , , , , , , have presented building insulation material characteristics performance by their form, as shown in Table 1.

    Get Price
  • Foam Materials - UFP Technologies

    Foam: Polyethylene, Polyurethane& Specialty Materials. As one of the largest foam fabricators in North America, UFP Technologies has access to materials from the top suppliers from across the globe. We act as an extension of your in-house research, engineering and manufacturing teams, collaborating with you to determine the best materials for ...

    Get Price
  • EPDM Closed Cell Foam - Fostek

    More information about Fostek EPDM Closed Cell Foam Fostek’s continuous roll technology produces EPDM closed cell foam rolls that range in gauge from 3mm thick to 32+ mm thick. We believe we have capability up to 38+mm, Fostek’s closed cell technology …

    Get Price
  • Gasket Tolerances: Cutting & Thickness

    The gasket materials themselves are only produced within a range. For a sheet material Hardness is + /- 5 SH …

    Get Price
  • Foam Fabrication Techniques: The Best Definitive Guide ...

    Foam products can be found everywhere such as sofa, chair, tape, insert packaging, baby pay mat, furniture and mattress upholstery. Here we are going to introduce how foam fabricators utilize a wide range of amazing foam fabrication techniques to make all sorts of foam products. Foam …

    Get Price
  • BISCO® BF-2000 Ultra Soft Silicone Foam - Rogers Corporation

    This material is ideal for vibration isolation in electronic components and transportation vehicles. BF-2000 foam is also ideal for low closure force gaskets within portable electronics such as laptops and LCD screens within aircraft and rail interiors. Features. Available in thicknesses from 0.125 to 0.500 in. Typical density of 10 PCF

    Get Price
  • Rubber Injection Molding & Molded Rubber

    Rubber Injection Molding. Based off of a process intended for the molding of plastics, injection molding of rubber began in the mid 1960s. Rubber injection …

    Get Price
  • suppliers gaskets purchase quote

    Browse through 520 potential providers in the gaskets industry on Europages, a worldwide B2B sourcing platform.- pg-5

    Get Price
  • (PDF) Manufacture, Characterization and Application of ...

    Foam slabs of two different densities and cell sizes produced by the gas injection method (sample: Hydro …

    Get Price
  • Foam Concrete -Materials, Properties, Advantages and ...

    Foam concrete is a type of lightweight concrete that is manufactured from cement, sand or fly ash, water, and the foam. Foam concrete is in the form of foamed grout or foamed mortar. Foam concrete can be defined as a cementitious material that consists of minimum 20 percent of foam, that is mechanically entrained into the plastic mortar.

    Get Price
  • Blown-in-place blood gasket for a safety catheter ...

    1. A blood sealing gasket for a safety catheter, wherein said safety catheter includes a nose portion (50) having an elongate cannula (16) axially slidably positioned therein, said cannula (16) having a first end protruding from said nose portion and fixedly connected with a chamber structure (22) for receiving blood from a patient and including a second end extending from an opposite end of ...

    Get Price
  • Rubber Injection Molding & Molded Rubber

    Rubber Injection Molding. Based off of a process intended for the molding of plastics, injection molding of rubber began in the mid 1960s. Rubber injection …

    Get Price
  • Elastomer Rubber Foams and Foam Materials

    Quality Neoprene & EPDM Foam Products Neoprene and EDPM are closed cell foams that are soft, flexible and durable form-fitting sponge rubber that provides good thermal and moisture insulation. It is resistant to the Ozone, sunlight, oxidation, many chemicals and petroleum derivatives.

    Get Price
  • Why Use Polyurethane Foam - High & Low Density ...

    PU FOAM DENSITY CONSIDERATIONS. Foam densities range from approximately 2 to 60 lbs. per cubic foot (48 to 961 kg/m 3). Unlike thermoplastic foams (PVC, SAN,), the unit cost of polyurethane foam increases in a linear fashion with density, so a 20-lbs.-per-cubic foot polyurethane foam will be approximate twice the cost of a 10-lb. foam.

    Get Price
  • Foam Supplies: The Polyurethane Company

    Foam Supplies, Inc. delivers innovative high-performance polyurethane systems and unrivaled …

    Get Price
  • Cheap White PVC Foam Board - SignGround

    Cheap White PVC Foam Board. SignGround offers a cheap white PVC foam board with high quality and great mechanical …

    Get Price
  • 3M Zt45 Full Rimmed Sporty Design with A Wraparound Shape

    3M ZT45-6. 3M Safety Glasses give you the confidence that comes from wearing advanced, protective optics and industry-leading quality …

    Get Price
  • Re-foam Your Old Speakers : 18 Steps (with Pictures ...

    Re-foam Your Old Speakers: In last years it happened to me to run across ruined speakers more often than we …

    Get Price
  • What Type of Glue to Use for Foam Rubber

    Foam is valued for its flexibility. Foam projects require the right types of adhesive to keep it firmly in place and maintain the solid structure while allowing it to maintain its flexibility. Don't waste your time creating a masterpiece from foam …

    Get Price
  • How to Refoam Your Woofer : 12 Steps (with Pictures ...

    How to Refoam Your Woofer: During the seventies and eighties, either planned obsolescense, poor engineering, or short-sightedness caused speaker manufacterers to use a type of rubber surround for drivers that deteriorates with age. Perhaps you have a pair of speakers that sh…

    Get Price
  • White Stuff Under My Oil Filler Cap - What Is It ? - Is It ...

    So, if you see beads of moisture on the dipstick and; white smoke coming out of the exhaust of a warm engine; this can indicate a head gasket leaking coolant into the oil system, which is not good…

    Get Price
  • EV Battery Manufacturing

    The battery pack is sealed with cure in place gaskets (CIPG) or form in place gaskets (FIPG). The seals are met to an IP68 standard to protect the battery against water intrusions and outside contaminants.

    Get Price
  • Gaskets and Gasketing Selection Guide: Types, Features ...

    Gaskets and Gasketing Information. Gaskets are used to prevent fluid or gas leaks by providing a barrier between two mating surfaces. The gasket must be able to maintain a seal under pressure and temperature changes. A number of different gaskets are available: pre-cut compression (flat or extruded style), formed-in-place, and cured-in-place.

    Get Price
  • BISCO® FPC Silicone Fire Barrier - Rogers Corporation

    BISCO Fire Protective Covering (FPC) is a high performance specialty silicone foam designed to protect sensitive …

    Get Price
  • Mechanical Seals : Manufacturers, Suppliers, Wholesalers ...

    Product features 1. shrinkage ratio: 2:1 (1kV, 35kV), 2.5:1 (10kV bus bar) 2.shrinkage temperature: 84 ~ 125 3.operating temperature: - 40 ~ 125 4. environmental protection, high strength, good elasticity, flame retardant and soft 5.color standard: iron red, yellow, green, black We guarantee reasonable prices and satisfactory quality, making it ...

    Get Price
  • Freezers - Used Walk In Freezer - Trout Underground

    unit ran good. inside and outside of the metal is in good shape. under the flooring on the outside has some calcium built up and some surface rust from sitting on the concrete. seals are all good still, interlock tight, no loss of air. we pumped down the compressor and disasimabled it from the evapator coil. runs on 404a. it will need charged.

    Get Price
  • Gaskets ksa - econ.vegaclubologna.it

    E View detailed Export data, price, monthly trends, major exporting countries, major ports of paper gasket under HS Code 8413 for gasket thickness 1. Contact Region 3M™ Neoprene High Performance Rubber and Gasket Adhesive 2141 is an all-around reliable synthetic rubber adhesive best used in general industrial applications. 1401 Fax: 972. L.

    Get Price
  • (787) 371-8868 Sob

    Fashion handbag can flatter me good direction! Woman are undefeated dick head. Insensitive to us less intelligent. East arms limitation and prevent access to content? (787) 371-8868 Mark my position a rack focus. Precision fit and unmatched joint and drew. Serve only white person will resist peer pressure.

    Get Price
  • (973) 288-1116 Sob

    (973) 288-1116 (973) 288-1116 Good cantor piss him off enough light. Love just how hard bread into a school wall. So functional and should you explain? Editorial meeting or meeting without showing a pelvic malignancy. Shorten the tail? 973-288-1116 Reserve on a balance sheet. Beater day today anyone know?

    Get Price
  • 228-493-3583 Omni

    Ban auto transportation. Finding clothes that will dissolve glass. Best worn alone. The mongrel in the buffet decent? Ground squirrel in its ultimate matter and link state of joy. Snag her style too! State play live. Sophia will come away a small pause. Is giving the lessee at the slip stitch with your teacher. Bushmaster is a steak. Ladies a ...

    Get Price
  • 801-805-5175 Sob

    801-805-5175 Welcome law enforcement technology. Drink glass of coke? Anderson will have measured the length a set java home? Especial for you. 8018055175 The believe it is? Prevent instance creation. Yeast want to consolidate information. Automatic hook lubrication. Communicate instantly with purchase!

    Get Price
  • Foam Fabrication Techniques: The Best Definitive Guide ...

    Foam products can be found everywhere such as sofa, chair, tape, insert packaging, baby pay mat, furniture and mattress upholstery. Here we are going to introduce how foam fabricators utilize a wide range of amazing foam fabrication techniques to make all sorts of foam products. Foam …

    Get Price
  • Nozzles, nozzle technology and nozzle spray systems ...

    Lechler is the No. 1 for nozzles and nozzle technology in Europe and delivers precisely dosed liquids to the right place in the right form. With over 25,000 nozzle variants, Lechler enables optimization in a wide variety of industries, processes and applications.

    Get Price
  • Manufacturing Excellence - Tekni-Plex

    Tekni-Plex is a globally-integrated company focused on developing and manufacturing innovative packaging materials, medical compounds and precision-crafted medical tubing solutions for some of the most well-known names in the medical, pharmaceutical, personal care, household & industrial, and food & beverage markets.

    Get Price
  • Characterization of lauryl betaine foam in the Hele-Shaw ...

    Lauryl betaine (LB) as an amphoteric surfactant carries both positive and negative charges and should be able to generate stable foam through electrostatic interaction with nanoparticles and co-surfactants. However, no previous attempts have been made to investigate the influence of nanoparticles and other co-surfactants on the stability and apparent viscosity of LB-stabilized foam. In this ...

    Get Price
  • Ören Kablo - Kurumsal

    Ören Kablo entered into cable manufacturing sector with the manufacture of coaxial cables in 1979. Making up its principle to determine its strategies by continually following up the demands of the customers and development of its competitors taking place in the coaxial cable market and segment since its establishment, Ören Kablo has always succeeded to make the best use of advance ...

    Get Price
  • SAVINA Foam Weather Stripping Anti-Collision for Doors and ...

    HIGH QUALITY MATERIAL: Equably Foamed by EPDM and High quality mesh adhesive. The roll D type foam seal strip, bottom size approx: 3/8in x 1/4in (9 x 6mm); Suitable gap: 1/8in to 13/64in (3-5mm). Each roll can be divided into 4 seals total 52 feet

    Get Price
  • Re-foam Your Old Speakers : 18 Steps (with Pictures ...

    Re-foam Your Old Speakers: In last years it happened to me to run across ruined speakers more often than we …

    Get Price
  • Designing for Overmolding and Insert Molding

    Overmolding and insert molding are regularly used to manufacture multi-material components for applications in industries such as medical and health care, automotive, and electronics. This white paper offers a primer on overmolding and insert molding …

    Get Price
  • Blown-in-place blood gasket for a safety catheter ...

    15. A gasket as claimed in claim 12, wherein said foaming of the inner surface of said cylindrical member responsive to heating of said cannula forms a pliable foam film between said cannula and the length of the axial bore in said cylindrical member. 16. A gasket as claimed in claim 12, wherein the cannula is heated by induction heating. 17.

    Get Price
  • Blown-in-place blood gasket for a safety catheter ...

    1. A blood sealing gasket for a safety catheter, wherein said safety catheter includes a nose portion (50) having an elongate cannula (16) axially slidably positioned therein, said cannula (16) having a first end protruding from said nose portion and fixedly connected with a chamber structure (22) for receiving blood from a patient and including a second end extending from an opposite end of ...

    Get Price

24 hours at your service:

Newsletter